cisco router 1720 manual

Avant de travailler sur un equipement, soyez conscient des dangers poses par les circuits electriques et familiarisez-vous avec les procedures couramment utilisees pour eviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformite aux reglements et consignes de securite) qui accompagne cet appareil.Sie befinden sich in einer Situation, die zu einer Korperverletzung fuhren konnte. Bevor Sie mit der Arbeit an irgendeinem Gerat beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfallen bewu?t. Ubersetzungen der in dieser Veroffentlichung enthaltenen Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information (Informationen zu behordlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerat geliefert wurde.La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformita alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo.Du befinner deg i en situasjon som kan fore til personskade. For du utforer arbeid pa utstyr, ma du vare oppmerksom pa de faremomentene som elektriske kretser inneb?rer, samt gjore deg kjent med vanlig praksis nar det gjelder a unnga ulykker. Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten.Encontra-se numa situacao que lhe podera causar danos fisicos.

• cisco 1720 router manual, cisco router 1720 manual, cisco router 1720 manual download, cisco router 1720 manual pdf, cisco router 1720 manual free, cisco router 1720 manual instructions.

Click Feedback in the toolbar, and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.We assume that Cisco 1700 router users are familiar with the terminology and concepts of local Ethernet and wide-area networking.Notes contain helpful suggestions or references to materials not contained in this manual.In this situation, you might do something that could result in equipment damage or loss of data.You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin tyoskentelet minkaan laitteiston parissa, ota selvaa sahkokytkentoihin liittyvista vaaroista ja tavanomaisista onnettomuuksien ehkaisykeinoista. Tassa julkaisussa esiintyvien varoitusten kaannokset loydat laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (maaraysten noudattaminen ja tietoa turvallisuudesta).Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels.

The correct public key to use in your correspondence with PSIRT is the one that has the most recent creation date in this public key server list:The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.The website is available 24 hours a day, 365 days a year, at this URL:If you have a valid service contract but do not have a user ID or password, you can register at this URL:The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:You and Cisco will commit full-time resources during normal business hours to resolve the situation.You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.There is little or no effect on your business operations.For current Cisco Press titles and other information, go to Cisco Press at this URL:You can access Packet magazine at this URL:You can access iQ Magazine at this URL. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty and license agreements from Cisco.com.You can download the reader from Adobe's website: Actual delivery times can vary, depending on the customer location.

Antes de comecar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos electricos, e com quaisquer praticas comuns que possam prevenir possiveis acidentes. Para ver as traducoes dos avisos que constam desta publicacao, consulte o documento Regulatory Compliance and Safety Information (Informacao de Seguranca e Disposicoes Reguladoras) que acompanha este dispositivo.Existe riesgo para su integridad fisica. Antes de manipular cualquier equipo, considerar los riesgos que entrana la corriente electrica y familiarizarse con los procedimientos estandar de prevencion de accidentes. Para ver una traduccion de las advertencias que aparecen en esta publicacion, consultar el documento titulado Regulatory Compliance and Safety Information (Informacion sobre seguridad y conformidad con las disposiciones reglamentarias) que se acompana con este dispositivo.Du befinner dig i en situation som kan leda till personskada. Innan du utfor arbete pa nagon utrustning maste du vara medveten om farorna med elkretsar och kanna till vanligt forfarande for att forebygga skador. Se forklaringar av de varningar som forkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrattelse av foreskrifter och sakerhetsinformation), vilket medfoljer denna anordning.These sections explain how to obtain technical information from Cisco Systems.The Documentation DVD is updated regularly and may be more current than printed documentation. The Documentation DVD package is available as a single unit. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you might have identified a vulnerability in a Cisco product, contact PSIRT:PSIRT can work from encrypted information that is compatible with PGP versions 2. x through 8. x.

You can access the Internet Protocol Journal at this URL: World-class networking training is available from Cisco.Auxiliary port Connects to a modem for remote configuration with Cisco IOS (black) software. Console port. For detailed (WIC1) information, refer to the Cisco WAN Interface Cards Hardware Installation Guide that comes with every card.Green Blinks when there is network activity on the Ethernet port. Yellow Blinks when there are packet collisions on the local Ethernet network. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Cisco 1700 Router Hardware Installation Guide 78-5405-03. You can load a new level of the operating system in every router in your network and then, when convenient, upgrade the whole network to the new level. Ethernet switch A switch connects pieces of network equipment (including the Cisco 1700 router) to create a network. The router supports up to two cards. You can order the cards when ordering the router, and they will be installed for you. Before making the power and network connections, simply set the router on a desktop, shelf, or other flat surface. For instructions on wall-mounting the router, refer to the “Wall-Mounting”. You must provide the following items for this. Each card has one or two WAN ports. This section describes the general procedure for installing a card in the Cisco 1700 router. Step 4 Confirm that the router has power by checking that the Step 5 PWR LED on the front panel is on. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Cisco 1700 Router Hardware Installation Guide 2-10 78-5405-03. The cable and adapter required for this connection are included with the router. Connect the gray adapter labeled MODEM to the other Step 2 end of the cable. Connect the DB-25 end of the adapter to the modem. Step 3 Cisco 1700 Router Hardware Installation Guide 2-12 78-5405-03. You must provide the screws. We recommend using pan-head or round-head screws.

If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative. Additional documentation can be found on Cisco.com.Accidently connecting the cable to the wrong port can damage your router.If a card is already installed, connect it to the WAN line according to the Cisco WAN Interface Cards Hardware Installation Guide that came with the card. To install a card in either slot, follow these instructions: Terminal emulation software should be configured with the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. The Cisco 1700 Router Software Configuration Guide describes how to configure the router using Cisco IOS software. If this adapter does not fit your PC console port, you must provide an adapter that fits.Continuous blinking can indicate a problem with the router.Refer to Table 1-4 in the hardware installation guide for detailed information.These sections explain how to obtain technical information from Cisco Systems.The Documentation DVD is updated regularly and may be more current than printed documentation. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices.Click Feedback in the toolbar, and select Documentation. After you complete the form, click Submit to send it to Cisco. Conventions This guide uses the following conventions for instructions and information: This note symbol means reader take note. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Cisco 1700 Router Hardware Installation Guide xiii 78-5405-03. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: If you have a valid service contract but do not have a user ID or password, you can register at this URL: Both new and experienced users will benefit from these publications.

17 Mar 2012 20 Dec 2016 interface card (WIC) for Cisco 1700, 2600, 3600, and 3700 series routers. It describes the benefits of the Loopbacks (including a manual button for a network line loopback) are provided for Cisco 1720 Router Hardware Installation Guide Cisco Aironet 2600 Series - Some links below may open a new browser window to display the document you selected. Sharepoint document converter,, Sample of thinking of you letters, Christmas lighted wire form angel, Form fc-il. Reload to refresh your session. Reload to refresh your session. Page Count: 12 Note Y ou must have Adobe Acrobat R eader to view and prin t PDF files. Y ou can do wnload the reader from Adobe’ s website:.adobe.com 3. T o read translated and localized warranty info rmation abou t your product, follo w these step s: a. Enter this part number in the W arranty Document Number f ield: 78-10747-01C0 b. Select the language in which you w ould like to vie w the document. c. Click Go. The Cisco warranty page appears. d. Read the document online, or click the PDF icon to d ownload and p rint the document in Adobe Portable Document Format (PDF). Actual deliv ery times can vary, de pending on the customer location. Cisco reserves the right to refund the purcha se price as its exclusiv e warranty remedy. To Receive a Return Materials Authorization (RMA) Number Contact the compan y from whom y ou purchased the product. If yo u purchased the product directly from Cisco, contact you r Cisco Sales and Service Representati ve. Connect the Router to the Local Network Y ou need to provide a straig ht-through Ethernet cable for conn ecting the router to the loca l Ethernet network. For more information on these cables, refer to the “C abling Specifications” chapter in the hardwa re installation guide that came wi th the router. The router senses the port speed and duplex mode and then operates at the same speed and duplex. Caution Al ways connect the Ethernet cable to the yello w ports on the router.

Accidently connecting the cable to the wrong port can d amage your router.If a card is already instal led, connec t it to the W AN line according to the Cisco W AN Interfac e Cards Hardware Installation Guide that came with the card. T o install a card in either slot, follow these instructions: Step 1 Set the power switch to the ST ANDBY ( ) position and confirm the router is not connected to the power suppl y. Step 2 Remove the screws that hold the slot cover in place, a nd then remove the slot cover. Figure 2 Locating the W AN Interf ace Card Step 3 Hold the card by the edges and li ne it up with the guide on the card slot. Step 4 Push the card into the slot until it is seated in the connector and the fron t panel is flush with the router rear panel. Figur e 3 Installing the W AN Interf ace Card Step 5 T i ghten the screws that are in the card. Step 6 Connect the card port to the W AN line according to the Cisco W AN Interface Cards Har dware Installation Guide.T erminal emulation software should be configured with th e following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. The Cisco 1700 Router Software Configuration Guide describes how to configure the router using Cisco IOS software. T ake the following steps to connect the router to one of these devices: Step 1 Connect one end of the blue console cable (included) to the CONSOLE port on the router rear panel. Step 2 Connect the RJ-45 end of the gray DB-9-to-RJ-45 adapter (i ncluded) to the unconnected end of the console cable. Figure 4 Connecting a PC to the Router Step 3 Connect the DB-9 end of the adapter to the console port (also called the serial port) on your PC.Step 2 Connect the separate power cord to the power socket on the power supply. Step 3 Connect the other end of the separate power cord to a power outlet. Figure 5 Connecting th e P ower Supply Step 5 Confirm that the router has power by checking that the PWR LED on the front panel is on.

If the screws are not properly anchored, the strain of the cables connected to the router rear-panel connectors could pull the router from the wall. Cisco 1700 Router Hardware Installation Guide 2-15 78-5405-03. Change the Configuration Register Connect an ASCII terminal or a PC running a. Compiled Fri 24-Jul-98 19:09 by aiyagari Image text-base: 0x80008084, data-base: 0x8084356C ROM: System Bootstrap, Version 11.3(19980612:045022) For more information on WAN interface cards, refer to the Cisco WAN Interface Cards Hardware Installation Guide that comes with each card. Cables—Check all the external cables that connect the router to the network. A pattern consists of a specific number of blinks that is repeated until the router is turned off. If the router experiences any of these problems, contact your Cisco reseller. Table 3-1 OK LED Blinking Patterns. The Cisco WAN Interface Cards Hardware Installation Guide lists the software requirements for each card. Table 3-3 list symptoms and possible causes of power problems. Cisco 1700 Router Hardware Installation Guide 3-10 78-5405-03. Cisco 1700 Router Hardware Installation Guide 3-11 78-5405-03. Cisco 1700 Router Hardware Installation Guide 3-12 78-5405-03. Table A-1 Router Specifications Description Specification Console port RJ-45 Auxiliary port RJ-45 Ethernet port RJ-45 Dimensions H x W x D 3.1 x 11.2 x 8.7 in. Cisco 1700 Router Hardware Installation Guide. Figure B-1 illustrates how to identify the console cable, which is also referred to as a rollover cable. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Pin 8 Cisco 1700 Router Hardware Installation Guide 78-5405-03. Opening the chassis requires a number one Phillips screwdriver. Follow these steps to open the chassis: Make sure the router is turned OFF and is disconnected Step 1 from the power supply. Step 6 Place the router bottom on an anti-static mat and begin installing memory. Cisco 1700 Router Hardware Installation Guide 78-5405-03.

Figure C-2 Cisco 1700 Motherboard—Memory Locations Rear panel of router WAN interface card slot WAN interface card slot DIMM slot Mini-Flash module slot Cisco 1700 Router Hardware Installation Guide 78-5405-03. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Locate the posts that protrude from the inside of the Step 2 chassis cover and corresponding openings on the chassis bottom. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Table D-1 lists, by geographic areas, the ISDN switch types supported by a Cisco 1700 router ISDN BRI interface. Use the isdn switch-type command followed by the corresponding keyword. You must reboot the router after entering this command for the change to take effect. The LDN is the number that a remote router dials to make a call to your router. Cisco 1700 Router Hardware Installation Guide 78-5405-03. Cisco 1700 Router Hardware Installation Guide 78-5405-03. We have 5 Cisco 1720 manuals available for free PDF download: Hardware Installation Manual, How To Use Manual, Quick Start Manual, Datasheet. Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series. Cisco 3900 Series, Cisco 2900 Series, and Cisco 1900 Series Integrated Services Routers Generation 2 Software Configuration Guide. Basic Router Quick Start Guide and the “Connecting Cisco Network Analysis Modules” chapter of Cisco To configure the Analysis-Module interface on the router CLI:. 10 Jun 2004 How to Configure Cisco 2600 Routers Routing Protocol Configuration.. configuring interfaces up and routing part, which has manual. 4 Dec 2001 Software Configuration Guide for the Cisco 2600 series, Cisco 3600 Series, and Cisco. Cisco 2600 Series Router Configuration Example A-1. Basic Configuration of Cisco 2600 Router. Basic Configuration Cisco 2600 Router. I decided to incorporate the Cisco 2600 into my previously designed network.

Blinking when the router is running a power -on self-test (POST). Continuous blinking can indicate a problem wi th the router. Refe r to the “T roubleshooting” chapter in the hardware installation guide for more information. WICO OK and WIC 1 OK Rear On when a W AN interface card is correctly installed in the corresponding W AN interface card slot. ETH ACT Front Blinking when there is network traffic on the local Ethernet LAN. WICO ACT and WIC1 ACT Front On solid or blinking when there is data traffic on the W AN interface card port(s). Refer to T able 1-4 in the hardware installa tion guide for detailed information. The Documentation DVD is updated regularly an d may be more current than printed documentation. The Documentation DVD package is available as a single unit.W e test our products internally before we release them, and we strive to corr ect all vulnerabilities quickly. PSIRT can work from encrypted information that is compatible with PGP versions 2. x through 8. x. Never use a revoked or an expired encryption key. The Cisco T e chnical Support W ebsite on Ci sco.com featur es extensive online support resources. In addition, Cisco T echnical Assistance Center (T AC) engineers provide telephone support. If you do not hold a valid Cisco service c ontra ct, contact your reseller. Cisco Technical Support Website The Cisco T echnical Support W ebsite provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copy ing and pasting show command output. Search results show an illustration of your product with the serial number label loca tion highlighted. Locate the serial number label on your product and record the in formation before placin g a service call. Submitting a Service Request Using the online T AC Servi ce Request T ool is the fastest way to open S3 and S4 service requests.

(S3 and S4 service requests ar e those in which your network is minimally impaired or for whi ch you require product information.) After you describe your situation, the T AC Service Request T ool pr ovides recommended solutions. If your is sue is not resolved using the recommended resources, yo ur service re quest is assigne d to a Cisco T AC en gineer.Severity 1 (S1)—Y our network is “down,” or there is a critical impact to your business oper ations. Y ou and Cisco will commit all necessary resources around the clock to re solve the situ ation. Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business opera tion are negatively affected by inadequate performance of Cisco product s. Y ou and Cisco will commit fu ll-time resources during normal business hours to resolve the situation. Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. Y ou and Cisco will commit resources during normal busine ss hours to restore service to satisfactory levels. Severity 4 (S4)—Y ou require information or assistance with Cisc o product capabilities, installati on, or configuration. Both new and experienced users will benefit from these publicati ons. Ea ch quarter, Packet del ivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and trou bl eshooting tips, configuration examples, cu stomer case studies, certification and training information, and links to scores of in -depth on line resources. Th e publication identi fies the challenges facing these companies a nd the technologies to help solve them, using real-worl d case studies and business strategies to help readers make sound technology investment decisi ons.All rights reserved. In this article we will cover how to build an effective CCNA lab.

Please do not skip any of this information, as it is all very important for you to understand so you get the most value for your money in purchasing your kit. So let’s start off with a basic concept that I hope we can all agree on.Dependent on what you do by mistake, you may see either the interface or protocol go down and based upon that it should give you a clue of where to start troubleshooting(hint, what layer is the interface at and what layer is the protocol at?). Anyway, you will come to find quite quickly that mistakes you make on Router 1 are affecting Router 4 all because you did not screw in a cable properly. No simulator can simulate that, so real routers and switches are invaluable.Cisco wants to make sure you really know your stuff on this exam. Basically they moved about 80% of the old CCNA 640-802 exam topics into the new ICND1 100-101 exam. So what does that mean to you. The days of having a high level understanding of what is happening and passing the exam are gone. You need to practice on more complex setups and really understand what is happening first hand. That is why when we revised our lab workbook. We made it much more complex and explain the concepts in detail as you do each lab. If you have a very limited budget, you can still receive value from only purchasing a single router over working with a simulator. However, with a single router you will not be able to see the main thing we are trying to accomplish; the propagation of route tables and the routing of data. The only way you can see if your configurations really work is to have at least two routers. Therefore, I strongly recommend that you purchase at least a dual router kit. But if you want the best experience, you will want to go with a three router kit. So let’s review this in a little more detail of what each scenario will provide to you. Two routers will allow you to be able to see route table information propagate, data propagation and path election.

In addition, you will see basic device elections. Three or more routers and you will get all of the above, more complex topologies and full device elections. Well let’s go into a little more depth and take a look at the slide below. Let’s say we need to ensure R2 is your DR (designated router). If we just have two routers, we can simply set the priority of R1 to zero which will make that router ineligible to be a DR. So then R2 would be the DR by default. But if we add a third router, then we don’t know if the DR will be R2 or R3. More than likely most companies you will work at will have more than two routers, right. So now you can see that we are going to have to do multiple configurations to influence which router is the DR in the more complex topology. So in this scenario, we need to increase the priority of R2 and leave R3 at its default priority to accomplish our goal. So hopefully now you can start to see why three routers are critical to really hammering home some of the CCNA concepts.Now compare that to the simple two router lab below it and see that it does not have load balancing, no multiple paths, no ability to set different costs on the links and obviously the route tables are not as complex. Let’s say one of the WAN links was configured super fast and the other one was a super slow WAN link. You are at the computer off of R3 and you are communicating with a server off of R1. The super fast WAN link goes down. What will your path be to the server off R1. Will the data travel across two routers traversing a super slow WAN link or traverse 3 routers utilizing fast links. Good question, huh? Now which lab topology do you think will give you a better learning experience? But with the recent 200-125 changes, inter-vlan routing is hit very heavy on the exam in various scenario questions. So if you can afford it, yes, switches are required.

With only a small margin of error between passing and failing, not fully understanding switching concepts such as VLANs, STP, and root elections could be the one question that stands between you passing and failing your exam. There will be some switch questions which are memorization based such as “What is a Layer 2 protocol used to maintain a loop-free network”. Thank goodness we memorized STP. That said, it would be nice for us to be able to actually see the switching concepts work. One switch will give you the ability to run the commands on the switch and allow you to memorize the correct syntax and context in which to run the commands. It will also allow you to do some of the VLAN labs. Three or more switches you will get all of the above and full device elections. Yes, you can get by. But you want to know this information inside and out. So three switches will give you the best learning experience. Let me prove it again. Spanning Tree Protocol is used to eliminate loops in our network, as loops are bad. So how can we determine which switch will be the Root Bridge. In general, it is based on the MAC address of the devices but it can be influenced by changing the priority on one or all of the devices. When a Root Bridge is elected, it is as if everything in the world will revolve around the Root Bridge. That dictates then which ports on the other switches are root ports, designated ports and non-designated ports. If also then impacts the states of the ports. So if the Root Bridge changes from Switch C to Switch B, then each port will change to a different type of port and state. Now we will have to figure everything out again from scratch. You might not fully understand this now, but by practicing with three switches in a complex topology such as this CCNA lab, you definitely will have a much deeper understanding of the technology at hand. Hopefully this example has fully convinced you of the value of a CCNA lab with three switches.